Axminster AWMS10 Manual de usuario

2005108004250mm Variable SpeedCompound Mitre SawAxminster Reference No: AWMS10User ManualWHITEAXMINSTERWwww.axminster.co.uk

10WHITEAXMINSTERWSpecification...www.axminster.co.ukAxminster No. AWMS10 (108004)Blade size.

WHITEAXMINSTERW11Illustration & Parts Description...FREEPHONE 0800 371822Turn tableTurn table positioning handleand clampClamping bolt handleTur

12WHITEAXMINSTERWIdentification & Description of the Mitre Saw...Operating The operating handle contains the trigger switch and is the handle use

WHITEAXMINSTERW13Illustration & Parts Description...FREEPHONE 0800 371822PointerTilt clampingknob and scaleLaser On/Off switchLock down pinTyp.

14WHITEAXMINSTERWIdentification & Description of the Mitre Saw...www.axminster.co.ukStabilising A length of 10mm bar bent and shaped to form a sup

WHITEAXMINSTERW15Illustration & Parts Description...45˚ degreesTilt and pivot assemblyTilt clampingknobTilt anglepointer LaserDust extraction A 48

16WHITEAXMINSTERWSetting Up the Machine...www.axminster.co.ukThe machine has been fully and accurately set up at the factory. If, however, you are not

WHITEAXMINSTERW17Setting Up the Machine...FREEPHONE 0800 371822Make sure the saw body frame is set in the upright position with the heel of the tilt

18WHITEAXMINSTERWSetting Up the Machine...www.axminster.co.ukDepth AdjustmentIt is possible to carry out a small adjustment to the depth of cut. ( i.e

WHITEAXMINSTERW19Setting the Laser...FREEPHONE 0800 371822Warning. Under no circumstances should you tamper with or modify the laser to try to i

WHITEAXMINSTERWIndex of Contents...Page No.Safety Protection SymbolsSAFETY!!!The symbols shown on the cover of thismanual advise that you wear the co

20WHITEAXMINSTERWSetting the Laser...www.axminster.co.ukAligning the Laser (Continued)Changing the BatteriesCheck that the laser line is a fine line,

WHITEAXMINSTERW21Table of Capacities...FREEPHONE 0800 371822With 250mm Diameter Blade fittedAlways use a 250mm Saw Blade with a rated speed in exces

22WHITEAXMINSTERWChanging the Saw Blade...www.axminster.co.ukFig 21Fig 22Arbor boltSaw plateflangeRemove the lower front guardBy trial and error, this

WHITEAXMINSTERW23Changing the Saw Blade...FREEPHONE 0800 371822Fig 23Fig 24Box spanner‘Y’ wrenchCheck the blade, the fabric, the sharpness, the set,

24WHITEAXMINSTERWIllustrated Parts Breakdown for the Mitre Saw...www.axminster.co.uk

WHITEAXMINSTERW25Maintenance...FREEPHONE 0800 371822(1) Keep machine clean(2) DO NOT allow the kerf slot to become jammed full of

26WHITEAXMINSTERWNotes...www.axminster.co.uk

WHITEAXMINSTERW27Notes...FREEPHONE 0800 371822

WHITEAXMINSTERW2005108004www.axminster.co.ukAxminster Devon EX13 5PH UKFREEPHONE 0800 371822Axminster Reference No: AWMS10250mm Variable Speed Comp

WHITEAXMINSTERW03Declaration of Conformity...FREEPHONE 0800 371822The undersigned, K. Bodenstein authorised by Zhangjiagang MFG Co., Ltd.No. 8 Haif

04WHITEAXMINSTERWWhat’s in the Box...www.axminster.co.ukModel Number: MIS 250E-21 No. 250mm Variable Speed Compound Mitre Saw1 No. Clamping Bolt H

WHITEAXMINSTERW05General Instructions for 230v Machines...FREEPHONE 0800 371822The following suggestions will enable you to observe good workingprac

06WHITEAXMINSTERWGeneral Instructions for 230v Machines...www.axminster.co.ukOnce the saw is mounted, carry out any setting operations, (mitre, tilt..

WHITEAXMINSTERW07General Instructions for 230v Machines...FREEPHONE 0800 371822General Safety Precautions for Compound Mitre Saw (Continued)DO NOT c

08WHITEAXMINSTERWGeneral Instructions for 230v Machines...www.axminster.co.ukWhen you have finished the cut, allow the saw to rise to its 'up&apo

WHITEAXMINSTERW09Initial Setup...FREEPHONE 0800 371822If required at this stage, insert the work support rails (remember to insert right through tot