Axminster Deluxe Instrucciones de operaciones

AWC4 250mm DeLuxe Combination MachineCode 501249AXMINSTERSERIESHobbyAT&M: 15/09/2014REF: 508306

Assembly Instructions10two pre-drilled holes on top of the extension table, see fig 10. Lift-up the 90˚ stop located to the corners of the extension t

Assembly Instructions11Fig16Fig 17Fig 18Dust extraction outletFlexible hoseFlexible hoseRip Fence AssemblyLocate the rip fence (A), rip fence extensio

Assembly Instructions12Clamping knob5) Locate the rip fence (A) and lower the clamp assembly over the guide rail (C), see fig 23. Fig 23- 24Fig 25Fig

Assembly Instructions13Fig 31Mount the overhand plane guard arm onto the side of the out feed table that corresponds to your preferred handing, then

Assembly Instructions14Spindle Moulder1) Remove the panel saw rip fence by lifting the locking lever up and lifting the fence away from the guide rail

Assembly Instructions154) Place a 90˚degrees square against the fence and adjust the assembly until the fence is perpendicular to the table, tighten t

Positioning the Machine16Fig 45Machine Foot Print2200mm1600mm3) Manoeuvre the machine to the chosen location making sure there is sufficient space all

Machine Foot Print172020mm1920mmSliding TableSliding Table

Illustration and Parts Description18Spindle Moulder Set UpPanel Saw Set Up

Illustration and Parts Description19Planer Set UpThicknesser Set Up

Index of Contents2Declaration of ConformityCopied from CE CertificateThe undersigned, T. Fuhrmann Authorised by Laizhou Planet Machinery Co., Ltd.Yut

Illustration and Parts DescriptionSaw tableSliding tableGuide railTable extension fenceSaw guardRip fence3 Way controlswitch assemblyFlexible hoseTilt

Illustration and Parts Description21Work clampSliding table locking knobAnti-kickbackassemblyGuide rollerassemblyClamping knobFence advancingclamping

Illustration and Parts DescriptionFence railMounting arm lockOut feed table adjusterThicknessing tablerise and fall controlCutter block guardWork clam

Illustration and Parts Description23Planer/Thicknesser ON/OFF switch (A) Emergency stop (B), Rise/Full clamp (C)Cutter block (A), In feed roller (B),O

Illustration and Parts Description24Fence securing clamp (A), Fence mounting bracket (B), Planer fence base (C), Elongated fence support bracket (D),

Illustration and Parts Description25Telescopic extension assemblyRiving knife (A), Saw blade (B), Scoring blade (C) Distance stop assembly90˚ degree e

Make sure the extension fence is up against the 90˚ extension fence stop, see fig 47 and using a 90˚ square, place it against the fence and the blade (

Setting Up the Machine27Fig 50NOTE: If you change the main blade saw blade at anytime, the kerf width of the replacement blade must be slightly narrow

Setting Up the Machine28Unsuitable, incorrectly mounted, dull, cracked or bent cutter knives can break or increase the risk of kickback considerably.T

Operating Instructions29Thicknessing Function• Rotate the cutter guard arm out of the way.• Remove the fence assembly.• Unlock the in feed/out feed t

What’s Included3Model Number: ML353GPanel Saw:1 No. 250mm AWC4 DeLuxe Combination Machine (95% assembled) 1 No: Rip Fence Assembly

Operating Instructions30• Feed the work piece straight across the machine table, holding the fingers close together and guiding the work piece with the

Operating Instructions316) • Check that the room is well lit. • Make sure that the saw table is clear of any tools. • Check that the saw guard i

Operating Instructions32from the slot and lay them aside. Repeat the process for the other two blades. If the block becomes difficult to hold located,

Operating Instructions33Changing the Panel Saw BladeChanging the Scoring BladeWARNING!! DISCONNECT THE MACHINE FROMTHE MAINS BEFORE CONTINUING!Raise t

Operating Instructions34WARNING!! DISCONNECT THE MACHINE FROM THE MAINS BEFORE CONTINUING!WARNING!! DISCONNECT THE MACHINE FROM THE MAINS BEFORE CONTI

Operating Instructions/Routine Maintenance35WARNING!! DISCONNECT THE MACHINE FROM THE MAINS BEFORE CONTINUING!Close the access door, raise the spindle

Parts Breakdown/List36Planer Thicknessser Assembly

Parts Breakdown/List37

Parts Breakdown/List38

Parts Breakdown/List39NO DESCRIPTION Q’TY1 Right and left Support plate13 Plate 24 Right plate 15 Bearing tube 111 Support base 412 Right cutter block

General Instructions for 230V Machines4The following suggestions will enable you to observe good working practices, keep yourself and fellow workers s

Parts Breakdown/List40132 Hand wheel 1505 Nut M10 8506 Screw M5x8 5507 Screw M5x8 4508 Hex bolt M8x16 2509 Hex nut M8 8510 Washer ɸ 5 12511 Washer

Parts Breakdown/List41NO DESCRIPTION Q’TY01 SAW BENCH AND MILLING BODY 102 PLANER THICKNESSER BODY 103 FRONT CONNECTED PLATE 104 BACK CONNECTED PLATE

Parts Breakdown/List42Panel Saw/ Spindle Moulder Assembly

Parts Breakdown/List43NO DESCRIPTION Q’TY01 Saw bench and moulder body 102 Saw bench and moulder table 103 Phillips screw M10X70 404 Hex nut MIO 1205

Parts Breakdown/List44Panel Saw Assembly 1

Parts Breakdown/List45NO DESCRIPTION Q’TY01 Small blade stand 102 Phillips screw M6X10 203 Adjusting plate 104 Phillips screw M8X30 205 Cap screw M5x1

Parts Breakdown/List46Panel Saw Assembly 2

Parts Breakdown/List47NO DESCRIPTION QTY01 Lock handle 102 Washer 8 103 Turning handle 104 Key A5X10 105 Flat washer 16 106 Connected plate 107 Inner

Parts Breakdown/List48NO DESCRIPTION Q’TY01 Screw M5x12 102 Hand wheel washer 103 Hand wheel ɸ12x ɸ125 104 Small clamp plate 105 Cap screw M6x12 206 F

Parts Breakdown/List49Continues Over...Spindle Moulder Assembly

Specific Safety Precautions5Panel SawMake sure the saw blade is the correct type for the job in hand. Do not force the saw, if the saw begins to ‘sta

Parts Breakdown/List50NO DESCRIPTION Q’TY01 Spindle seat 102 Hex locking nut M12 103 Spindle 104 Bolt M5X16 305 Spring cover 106 Bearing 6206-2Z/Z2 10

Parts Breakdown/List51NO DESCRIPTION Q’TY01 Support plate 202 Knob bolt 203 Flat washer 6 204 Sliding block 205 Hex screw M6x16 806 Flat washer 6 807

Parts Breakdown/List52Rip-Fence Assembly NO DESCRIPTION QTY1 Sliding Plank 12 M6 Screw 23 M6 Nut 24 Washer 25 Horizontal Staff 16 Horizontal Staff Ca

Parts Breakdown/List53NO DESCRIPTION Q’TY01 Knob bolt 102 Horizontal bar 103 Clamp sleeve 104 Knob (M8) 105 Cap screw M5X12 206 Washer 6 207 Nut M5 20

Wiring Diagram54

Cutter Block Accessories55 Two sizes of limiter cutter block, 78mm and 100mm, both with 30mm bores, which designed to accept the range of Euro cutters

Axminster Tools & Machinery LtdWeycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukPlease dispose of packaging for the product in a responsib

Specific Safety Precautions6In addition to the safety requirements contained in these Operating Instructions and your country’s applicable regulations,

Specific Safety Precautions7Check the height of the thicknessing table. Engage the autofeed mechanism.Periodically, clean any excess build up of resin

Assembly Instructions8PLEASE NOTE: Some of this assembly procedure is best accomplished by two persons. Although the tasks are not impossible, some of

Assembly Instructions92) Locate the steel pin plate (A) , line up the pins with the elongated slots in the extension table (B) and lower the plate int